fbpx

Amana, Daikin, Goodman Furnace Error Codes

Look up error codes to identify furnace problems and estimate repair costs.

Locating the furnace error code

Refer to the furnace glossary if you need help identifying furnace parts or terms.

All high-efficiency furnaces and most mid-efficiency furnaces show error codes on the control board, either as a flashing LED sequence or on a display .

The furnace control board is almost always in the lower compartment. You can view the error code LED or display through a small, clear plastic inspection port in the centre of the lower furnace cover.

If the control board isn’t in the lower compartment, it’s in the upper compartment.

Furnaces with upper and lower furnace covers — The inspection port is usually on the lower furnace cover and is accessible without removing the cover.

Furnaces with a one-piece front cover — Remove the front cover first. The inspection port is usually on the secondary cover for the lower compartment.

If the control board is in the upper compartment — You need to remove the upper furnace cover. If there are thumb screws, loosen them and pull the cover out from the screw location. If there are no screws, slide the cover straight up, then pull it out.

Error codes

Don’t turn off the power to the furnace while troubleshooting — unless instructed otherwise. Turning off the power clears the current error code.

Observe the flashing LED sequence or display code, which may repeat in a loop. Watch it carefully, make note of the sequence or digits, and match it up with the corresponding code below:

LED off

No power

Continue to the Power diagnostic

LED on, not flashing

Normal operation

Continue to the Secondary diagnostic

LED flashing rapidly

Line voltage polarity incorrect

Possible wiring, transformer, or control board failure. Requires professional diagnosis.

1 flash with extended pause

Lockout due to excessive retries

Continue to the Secondary diagnostic

2 flashes

Closed pressure switch with inducer off

Faulty pressure switch or control board.

3 flashes

Open pressure switch with inducer on

Continue to the Secondary diagnostic

4 flashes

High limit switch open

Continue to the Secondary diagnostic

5 flashes

Flame sensed with gas valve off

Possible faulty gas valve or control board. Professional diagnosis required.

6 flashes

Rollout switch open

Cracked primary heat exchanger or plugged secondary heat exchanger. Requires professional diagnosis.

7 flashes

Low flame signal

Faulty flame sensor, igniter, or gas valve.

8 flashes

Igniter error

Faulty igniter or control board.

9 flashes

Grounding or polarity reversed

Faulty wiring or control board.

Error code not listed

Other furnace problem

Continue to the Secondary diagnostic

On this page:

Furnace repairs should only be performed by a certified technician.

This website is for informational purposes only. Advanpro Ltd. is not liable for property damage, personal injury, or death caused directly or indirectly by actions taken as a result of the information provided here.

Repair Wiring or Control Board

$199 or $899 to $1399 + GST

Mention this diagnosis from the troubleshooting guide when you book:

(403) 873-7779

Call us 24 hours, 7 days a week

[email protected]

Email us, get a reply in 1 business day

Repair Igniter or Control Board

$379 or $899 + GST

Mention this diagnosis from the troubleshooting guide when you book:

(403) 873-7779

Call us 24 hours, 7 days a week

[email protected]

Email us, get a reply in 1 business day

Repair Pressure Switch or Control Board

$379 or $899 + GST

Mention this diagnosis from the troubleshooting guide when you book:

(403) 873-7779

Call us 24 hours, 7 days a week

[email protected]

Email us, get a reply in 1 business day

Repair Flame Sensor, Igniter, or Gas Valve

$199, $379, or $899 + GST

Mention this diagnosis from the troubleshooting guide when you book:

(403) 873-7779

Call us 24 hours, 7 days a week

[email protected]

Email us, get a reply in 1 business day

Professional Diagnosis Required

$109.95 regular hours call-out & diagnosis fee

Our technician will identify the problem and tell you how much it will cost to repair. Once you know the problem and the cost, you can decide if you want to proceed.

(403) 873-7779

Call us 24 hours, 7 days a week

[email protected]

Email us, get a reply in 1 business day